Herz pelletfire 20/20 Operating Instructions Manual Download Page 60

Page: 60 / 100

Menu navigation and adjustment values

9.13.11

Additional boiler

The recommended hydraulic schemes are shown in appendix 15.1

Navigation:

→

Additional boiler

Screen:

By pressing the button:

the „additional boiler status“ menu will be displayed
(Schematic representation of the boiler and overview of various values)

the menu for the "settings" will be displayed

the menu "inputs / outputs" will be displayed

the menu "operating hours" will be displayed

Term

Description

Unit

Menu „additional boiler status“

Status 1

Boiler temperature

Indicates the boiler temperature (40-80)

°C

Flue gas temperature

Indicates the flue gas temperature

°C

Pump

Indicates the state of the back flow pump (ON/OFF)

Release / additional
boiler

Indicates the state of the release of the additional boiler: (ON/OFF)

Automatic:

Release ON / OFF

Manual:

additional boiler active / inactive

Menu "Settings"

Settings

Waiting period

Automatic:

waiting time for release of the additional boiler (if required)

Manually:

additional boiler minimum operation time till additional boiler is

available again

Setting the waiting time (1-900), until the additional boiler starts.

min

Pump trigger

Setting up pump trigger (25-65)

°C

Summary of Contents for pelletfire 20/20





































































































Search results

Summary of Contents for pelletfire 20/20

Reviews:

Herz pelletfire 20/20, Operating Instructions Manual, Page: 60 / 100

Search results

Summary of Contents for pelletfire 20/20

Reviews: