Herz pelletfire 20/20 Page 33 Operating Instructions Manual Download

Page: 33 / 100

Menu navigation and adjustment values

9.11

Module

Navigation:

→

Screen:

By pressing the button:

BOILER

the „boiler values“ menu will be displayed

BUFFER

the „buffer values“ menu will be displayed

HOT WATER TANK

the „hot water tank values“ menu will be displayed

HEATING CIRCUIT

the „heating circuit values“ menu will be displayed

If several modules have been created, you can navigate through the menu of
the modules (up or down).

In the Module overview by clicking on the respective
module name, a separate name (module name) can be
assigned for each module.

To do this, first press the name above. Then click on
the field with the current name. An input window
appears. The desired name can be entered.

In the case of a language change or deleting, the
default name will be restored.

Summary of Contents for pelletfire 20/20





































































































Search results

Summary of Contents for pelletfire 20/20

Reviews:

Related manuals for pelletfire 20/20

Brands by name

Popular brands

Herz pelletfire 20/20, Operating Instructions Manual

Search results

Summary of Contents for pelletfire 20/20

Reviews:

Related manuals for pelletfire 20/20

Brands by name

Popular brands