HermanMiller Embody 100210688 Manual Download Page 97

Page: 97 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YHS REV A

Close Lid. Insert Spring into tilt assembly.

Use flat blade screwdriver to reconnect
Spring to tilt assembly.

Position Rack onto assembly. Install
Flange Bushing and Shoulder bolt.

Shoulder Bolt

Flange Bushing

Tighten Shoulder Bolts to 250 in/lbs.

Install 2 Hex Washer Head Screws. Tighten
screws to 55 in/lbs.

Hex Washer
Head Screw

Secure Adjuster to tilt with Socket Head
Screw. Torq to 75 in/lbs.

Socket Head
Screw

Spring

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands