manualshive.com logo in svg

HermanMiller Embody 100210688, Manual

Share
Download
HermanMiller Embody 100210688 Manual Download Page 52

©

2000 Herman Miller, Inc., Zeeland, Michigan  Printed in U.S.A.

®        Action Office, Aeron, Ambi,Arrio, Beirise Collection, Co/Struc, Custom Choices, Eames, Equa, Equa 2, Ergon 2, Ergon 3, Ethospace, E-wall

Hollington, Liaison, Meridian, Newhouse Group, Passage, Pellicle, Phoenix, Proper, Radian, Relay, Scooter, Super Room, Systems Bridge,   

           and V-wall are registered trademarks of Herman Miller, Inc.
™

L

, 

Z

, 

Y

, Caper, Burdick Group, Chadwick, Flex-Edge, Florence, ID, Kiva, Levity, Milafin,  Potomac, Prospects, Q, Raleigh, 

          Reaction, Red, Resolve, SQA, and Traverse are trademarks of Herman Miller, Inc.

 Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make  

         changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJ0 REV A

7. Replace back tension adjustment knob

 

7

    

     
    

1. Remove back tension adjustment rod by 

1

RIGHT ARM

4. Replace with new arm.

5. Re-install bolts snug.

6. Tighten to 85 in/lbs.

2. “Repeat steps 2-6 of Left arm 

    by pushing all the way in and then strike
    with palm of hand until seated, and
    audible click should be heard. 

4

    wiggling up and down while pulling out to

    

diesengage.

 

     Replacement Procedures”.

5

BOLTS

Summary of Contents for Embody 100210688

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands