manualshive.com logo in svg

HermanMiller Embody 100210688, Manual

Share
Download
HermanMiller Embody 100210688 Manual Download Page 61

©

2008 Herman Miller, Inc., Zeeland, Michigan  Printed in U.S.A.

™

L

, 

Z

, 

Y

, Embody, are trademarks of Herman Miller, Inc.

 

 Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make  

         changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YHY REV B

8

Remove two lower front link shoulder bolts 
and bushings using t-40 torx wrench

Bolt

Bolt

9

10

Remove seat. Set tilt tension to minimum.

11

12

Pull lower cover forward

Lift up front of seat assembly

Locate wire clip for tilt tension knob.  Slide flat 
headed screwdriver under cable collar.  Pry 
up gently until cable collar is free.

13

Grasp the cable and push it forward to release 
ball end from cylinder.

Tilt Tension Knob

Summary of Contents for Embody 100210688

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands