HermanMiller Embody 100210688 Manual Download Page 24

Page: 24 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJ9 REV A

Embody

™

Seat Replacement

PARTS INCLUDED:

TOOLS REQUIRED:

Seat Assembly

Bolts

Remove back tension adjustment rod by wig-
gling up and down while pulling out to disen-
gage

T-30 T-40

Tension
Adjustment Rod

Remove lower spine bolts using t-40 torx
wrench

Remove lower back bolts using t-40 torx
wrench

Torx bits

Ratchet

Torque Wrench

T-27

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands