HermanMiller Embody 100210688 Manual Download Page 69

Page: 69 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YHX REV A

Remove Wire Clip from end of Tilt Limiter
Lever. Set Clip aside.

Pull Tilt Limiter Lever free from assembly.

Tilt Limiter Lever

Wire Clip

Remove Shoulder Bolt and Flange Bushing
from each side of Rack.

Rotate Rack and pull free from assembly.

Install 2 U-Clips onto replacement Rack.

Remove 2 Hex Washer Head Screws.

Hex Washer

U-Clip

Shoulder Bolt &

Flange Bushing

Head Screw

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands