HermanMiller Embody 100210688 Manual Download Page 33

Page: 33 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJ8 REV A

Set front of rear tilt cover onto bushings in
pivot assembly. Press down on back of cover
making sure clips fully engage into slots in tilt.

Bushing

Clip

Remove Wire Clip from end of Tilt Limiter
Lever. Set Clip aside.

Pull Tilt Limiter Lever free from assembly.

Insert replacement Tilt Limiter Lever into
assembly.

Return Wire Clip to end of Lever.

Tilt Limiter Lever

Wire Clip

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands