HermanMiller Embody 100210688 Manual Download Page 22

Page: 22 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJB REV A

Post

Tilt

Clip

Align the spine to the tilt, and seat loca-
tor post and clips to the to the back
attachment points as shown in the fig-
ure on the right. Replace the Seat Clips
as shown in the figure below if they
popped off during step 4.

The Seat back posts should engage
into the Seat Clips as illustrated in the
figures below.

Note. If Clips popped off during disassembly
replace them as shown in Step #29.

Clip

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands