HermanMiller Embody 100210688 Manual Download Page 39

Page: 39 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJ6 REV A

Using the T-27 Hand Tool remove the Spine
Cap Screws by turning in a counter-clockwise
direction. Remove the Spine Caps and Pivot
Pin and set aside

Lift up on Antler to release it from upper spine

Remove the two top antler attachment screws
using a t-27 torx bit

Pull one end of the Antler away from top frame
and remove

Assemble replacement Antler onto Back.

Pivot

Hinge

Spine Cap

Antler Attachment

Cover

Pin

Screw

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands