HermanMiller Embody 100210688 Manual Download Page 11

Page: 11 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJC REV A

Remove the two top antler attachment screws
using a t-27 torx bit

Pull one end of the Antler away from top
frame and remove

Assemble Antler onto replacement Back.

Antler Attachment
Screw

Make sure the Dome tabs are placed over
back collar as shown when assembling.

Fold Dome over antler.

Firmly press down making sure christmas
tree clips fully engage into antler.

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands