HermanMiller Embody 100210688 Manual Download Page 89

Page: 89 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YHT REV A

Install single lower bolts into each arm hous-
ing using t-27 torx wrench (repeat for oppo-
site side) (75 in/lbs)

Bolt

Return both arms or plugs using t-30 torx
wrench (repeat for opposite side) (75 in/lbs)

Check to make sure the seat fabric flaps are
secure over the seat clips and do not visibly pro-
trude where the spine engages the seat.

Install bushings and shoulders bolts using
t-40 torx wrench. (250 In/lbs)

Note. If Clips popped off during disassembly
replace them as shown in Step # 36.

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands