HermanMiller Embody 100210688 Manual Download Page 77

Page: 77 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YHW REV C

Pull tension knob assembly free from housing.

Remove wire clip from tilt tension knob
assembly.

While pulling out on front ears, pull front tilt
cover forward and out.

Note: For Chairs manufactured before
4/20/2010

15a

Remove fulcrum cover removing four Screws.

Slide new front tilt cover in and back over tilt.

Assemble new fulcrum cover to tilt assembly.
(Cover not shown for clarity.)

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands