manualshive.com logo in svg

HermanMiller Embody 100210688, Manual

Share
Download
HermanMiller Embody 100210688 Manual Download Page 88

©

2008 Herman Miller, Inc., Zeeland, Michigan  Printed in U.S.A.

™

L

, 

Z

, 

Y

, Embody, are trademarks of Herman Miller, Inc.

 

 Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make  

         changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YHT REV A

29

28

27

31

30

Install 2 Hex Washer Head Screws.  Tighten 
Screws to 55 in/lbs.

Hex Washer
Head Screw

26

Return Wire Clip to end of Lever.

Wire Clip

Insert Tilt Limiter Lever into assembly.

 

Tilt Limiter Lever

Set front of rear tilt cover onto bushings in 
pivot assembly.  Press down on back of cover 
making sure clips fully engage into slots in tilt. 

Bushing

Put the back edge of the seat assembly out-
side of the rack and rotate front of the seat 

Rotate front link cover down until holes are 
aligned.

Summary of Contents for Embody 100210688

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands