HermanMiller Embody 100210688 Manual Download Page 18

Page: 18 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJB REV A

Clip

Remove back assembly by sliding fingers
between the seat and back and pull the back
corners away from the seat until free

Note. If Clips pop off please discard.

Depress end of Fabric Cable. Remove Hook
on Fabric Cable from Loop on fabric cover.

Lay chair on back. Grasp Seat Slide Handles.
Slide seat out to longest position.

Loop

Fabric Cable

Handle

Pull Seat Slide Guide free from Seat Post.

Remove Fabric Cable from Seat Slide Guide.

Fabric Cable

Seat Slide Guide

Seat Post

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands