HEIDENHAIN TNC 426 B User Manual Download | Manualshive

Page: 58 / 362

background image

42

4 Programming: Fundamentals of NC, File Management,

Programming Aids, Pallet Management

Calling the file manager

Press the PGM MGT:
The TNC displays the file management window
(see Fig. at top right for default setting. If the
TNC displays a different screen layout, press the
WINDOW soft key)

The narrow window at left shows three drives . If the TNC is
connected to a network, it also displayed the connected network
drives. Drives designate devices with which data are stored or
transferred. One drive is the hard disk of the TNC. Other drives are
the interfaces (RS232, RS422, Ethernet), which can be used, for
example, to connect a personal computer. The selected (active)
drive is shown in a different color.

In the lower part of the narrow window the TNC shows all
directories of the selected drive. A drive is always identified by a
file symbol to the left and the directory name to the right. The TNC
displays a subdirectory to the right of and below its parent directory.
The selected (active) directory is depicted in a different color.

The wide window at on the right side shows all the files that are
stored in the selected directory. Each file is shown with additional
information that is illustrated in the table on the next page.

Display

Meaning

FILE NAME

Name with max. 16 characters
and file type

BYTE

File size in bytes

STATUS

Property of the file:

E

Program is in the
Programming
and Editing
mode of operation

S

Program is in the
Test Run
mode of operation

M

Program is in a
Program Run mode of
operation.

P

File is protected against
editing and erasure

(Protected)

DATE

Date the file
was last changed

TIME

Time the file
was last changed

4.4 File Manag

ement with

A

dditional F

unctions

Ekap4.pm6

30.06.2006, 07:03

42

www.EngineeringBooksPdf.com

«
...
56
57
58
59
60
...
»

Summary of Contents for TNC 426 B











































































































































































































































































































































































Reviews:

No comments

Related manuals for TNC 426 B

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 3

Brand: Warren Controls Pages: 16

Brand: ZIMO Pages: 38

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: Jafar Pages: 10

Brand: BADLANDS Pages: 2

Brand: Eaton Pages: 6

Brand: Eaton Pages: 35

Brand: Eaton Pages: 18

Brand: Eaton Pages: 73

Brand: Eaton Pages: 4

Cutler-Hammer IQ DP-4000

Brand: Eaton Pages: 87

Brand: Eaton Pages: 14

Brand: Eaton Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands