Harris NetWave, Operation & Technical Manual

Page: 54 / 90

Revision A • 6/06
H A R R I S C O R P O R A T I O N
3-8
3 Using NetWave
MONITOR PANEL, RIGHT COLUMN CONTROL DETAIL
STUDIO MONITOR SOURCE
All studio outputs use the same monitor source. The selected source is indicated by the lit button.
Only one button can be selected at a time.
PGM 1-4 — PGM 1-4 — PGM 1-4 — PGM 1-4 — PGM 1-4 — When lit, routes the selected Program bus to the studio outputs.
EX EX EX EX EXT 1, T 1, T 1, T 1, T 1, EX EX EX EX EXT 2 — T 2 — T 2 — T 2 — T 2 — When lit, routes the selected External signal to the studio outputs.
DISPLAYS
V V V V VistaM istaM istaM istaM istaMax Link ax Link ax Link ax Link ax Linked — ed — ed — ed — ed — When lit, indicates the console is properly connected and communicating
with a VistaMax audio management system. If it is not lit, the console is not connected to a
VistaMax system and does not have networking capability.
S S S S Studio M tudio M tudio M tudio M tudio Mut ut ut ut ute — e — e — e — e — When lit, indicates the room monitor output and studio warning logic are
active due to one or more channels, that have a studio mic as their input, being turned on and
assigned to a program bus. When unlit, no studio mic is turned on.
STUDIO CONTROLS
M M
M M Monit
onit
onit onit onitor —
or —
or — or — or — Adjusts the output level of the studio monitor (ST MON) output.
T T T T Ta l k a l k a l k a l k a l kback — back — back — back — back — Adjusts the amount of talkback to the studio that feeds the studio monitor output.
Set the talkback control to full off if talkback should not feed the studio speakers.
T T T T Talk t alk t alk t alk t alk to S o S o S o S o Studio — tudio — tudio — tudio — tudio — While pressed, routes the control room talk mics, pre-switch and pre-fader,
to the studio host output and to the room monitor output through the Talkback control. Talk mics
are inputs defined as CR MIC TLK SRC (control room mic talk source) and that are active (i.e., if
the talk mic is the B input, then the B source has to be selected on the channel. If the A source is
active, then that mic’s audio will not feed the talk output).
EVENT TIMER CONTROLS
A A
A A Aut
ut
ut ut uto R
o R
o R o R o Reset —
eset —
eset — eset — eset — When lit, allows the event timer to be reset when a channel, that has timer reset
enabled, is turned on. This resets the timer to 00:00.0 and starts counting upward. When unlit,
the event timer does not receive reset commands from the channels.
Reset — Reset —
Reset — Reset —
Reset — Resets the event timer to 00:00.0 and starts counting up. Press Reset and Stop together
to reset and stop the timer at 00:00.0.
Hold — Hold —
Hold — Hold —
Hold — Press and hold the button to freeze the event timer display to show the elapsed run time
when the button was pressed. The event timer continues to count during this time. Releasing the
button returns the event timer display to show the current run time.
S S S S Star tar tar tar tart — t — t — t — t — Starts the event timer counting up from the displayed time.
S S
S S Stttttop —
op —
op — op — op — Stops the event timer and displays the elapsed time. Press Start to continue counting up
from the displayed time. Press Reset and Stop together to reset the timer to 00:00.0.