Revision A • 6/06
H
A
R
R
I
S
C
O
R
P
O
R
A T
I
O
N
3-3
3 Using NetWave
BUS
ASSIGNMENT
SECTION
DUAL FADER PANEL
Each panel has two channel strips for independent control of two audio signals. Each channel has two sources (A
and B) that are board operator selected. The A and B labels (normally replaced by custom labels to identify the
input signal name) light up to indicate the active source on that channel.
BUS ASSIGNMENT SECTION
P R
P R
P R
P R
P RO G R
O G R
O G R
O G R
O G RAM 1,
AM 1,
AM 1,
AM 1,
AM 1, 2,
2,
2,
2,
2, 3,
3,
3,
3,
3, 4
4
4
4
4 —
—
—
—
—
When lit, routes the channel audio, post
fader and post switch, to any combination of the four Program buses.
OFFLINE —
OFFLINE —
OFFLINE —
OFFLINE —
OFFLINE —
When lit, routes the channel audio, pre-switch and
typically pre-fader (may be set post-fader), to the Offline bus.
Note:
Note:
Note:
Note:
Note: The two Telco channels can have an assignment button winking,
or blinking. This indicates the bus assigned to the Telco mix-minus and
Telco record outputs. See page 3-11 for Telco operation specifics.
FADER CONTROL SECTION
A and B —
A and B —
A and B —
A and B —
A and B —
The lit button indicates the active source, along with the lit
A or B label in the channel display. To change the source, press the unlit
source button (Take will flash), then press the flashing Take button..
T
T
T
T
TAKE —
AKE —
AKE —
AKE —
AKE —
Switches the input source (A to B or B to A) when pressed
while flashing. If the channel is on, this will force the channel off.
F
F
F
F
Fader —
ader —
ader —
ader —
ader —
100mm channel level control with dB indications to show
relative attenuation. For unity gain, set the fader to the red line (-12
dB). This makes a n4 dBu analog input signal appear as a
-20 dBFS (0 VU) signal on the meters.
CUE —
CUE —
CUE —
CUE —
CUE —
When lit, routes pre-fader, pre-switch audio to the cue speaker
without affecting the on-air signal. On CR MIC channels, the cue button
is momentary and the signal only feeds the Aux meter. On line inputs, it
toggles cue on and off. Cue feeds the cue speaker and, when AutoCue is
lit on the Monitor panel, also feeds the operator headphones. Cue levels
are also typically displayed on the Aux meter while active.
ON —
ON —
ON —
ON —
ON —
Press to turn the channel on. The button lights, routing the
audio to the selected buses. Logic control commands may also be
initiated, depending upon the logic settings for that source.
OFF —
OFF —
OFF —
OFF —
OFF —
Press to turn the channel off and remove the audio from all
selected buses (except for Offline, if selected). The button may not light
on peripheral devices when the source is set to respond to ready
commands to indicate its status. Logic control commands may also be
initiated, depending upon the logic settings for that source.
T
T
T
T
Ta l k
a l k
a l k
a l k
a l kback —
back —
back —
back —
back —
Pressing the lit On or Off button on a Telco channel
routes the CR talk mics, pre-switch and pre-fader, to that Telco channel’s
mix-minus IFB output. The Telco’s lit button blinks rapidly while talk is
active as does the talk mic channels off buttons. If a CR talk mic channel
is on, it is muted from the buses while talking.
FADER
CONTROL
SECTION
CHANNEL
DISPLAY
