Revision A • 6/06
H
A
R
R
I
S
C
O
R
P
O
R
A T
I
O
N
2-28
2 Installation
BASIC PERIPHERAL DEVICE LOGIC CONNECTION EXAMPLE
This example shows a peripheral device (with basic logic functions like the CD player shown below) connected
to an Channel Logic I/O connector.
CHANNEL LOGIC
CONNECTOR
DENON DN-SERIES
CD PLAYER LOGIC
SIGNAL PIN
PIN SIGNAL
BRN
BLK
GRN
RED
WHT
Pulse Common
Enable Logic Inputs (+)
Stop Pulse
Start Pulse
Ready (-)
6
4
5
11
8
23
22
3
2
16
15
Switch Common
Tally Common
Pause N.O.
Play N.O.
Standby/Cue Tally
Pause Tally
PARTS LIST
Cable: 19-119 (Belden 8445 or equiv.)
Diodes: 11-7 (1N4001 or equiv.)
25-pin DSub: 15-854 (DB-25P)
12-pin MOD IV housing: 14-490 (Tyco-AMP 87922-2)
MOD IV contacts: 15-938-1 (Tyco-AMP 102128-1)
CR1
CR2
PIN #
PIN #
PIN #
PIN #
PIN # SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
1
LOGIC GROUND
Logic ground
2
CUE INPUT (-)
Remote Cue switch input (active low)
3
OFF INPUT (-)
Remote Off switch input (active low)
4
ENABLE L
ENABLE L
ENABLE L
ENABLE L
ENABLE LOGIC INPUT
OGIC INPUT
OGIC INPUT
OGIC INPUT
OGIC INPUTS (+)
S (+)
S (+)
S (+)
S (+)
Jumper to +VDC to enable switch inputs
5
ST
ST
ST
ST
STOP PULSE
OP PULSE
OP PULSE
OP PULSE
OP PULSE
Stop command output, N.O. contact
6
PULSE C
PULSE C
PULSE C
PULSE C
PULSE COMMON
OMMON
OMMON
OMMON
OMMON
Start/Stop Pulse common, C contact
7
+5 VOLT LOGIC SUPPLY
5 volt source
8
READ
READ
READ
READ
READY INPUT (-)
Y INPUT (-)
Y INPUT (-)
Y INPUT (-)
Y INPUT (-)
Remote Ready switch input (active low)
9
ON INPUT (-)
Remote On switch input (active low)
10
+5 VOLT LOGIC SUPPLY
5 volt source to enable switches
11
ST
ST
ST
ST
STAR
AR
AR
AR
ART PULSE
T PULSE
T PULSE
T PULSE
T PULSE
Start command output, N.O. contact
12
+5 VOLT LOGIC SUPPLY
5 volt source for switch tallies
Notes:
+VDC is b5 and +40 VDC.
Outputs can switch voltages up to +60 VDC at 350 mA total
B
B
B
B
Bold
old
old
old
old
indicates connections used in this example.
CHANNEL LOGIC I/O CONNECTOR SIGNAL TABLE
(wire insertion end view)
1 2 3 4 5 6
7 8 9 10 11 12
DSP & I/O Card
Denon CD Player,
connected to
channel 4, source A
To Logic I/O 4
To Digital Input 4
951
Channel 4 Parameter Settings (A source)
for a peripheral device using line logic
EXAMPLE OF CD PLAYER CONNECTED TO INPUT 4
1. Input: set to Digital
2. Mode: set to Stereo
3. Function: LINE (no LEDs lit)
4. Logic Active: On
5. Timer Reset: On
6. Remote Off LED Ctrl: On
(for Ready control of Off LED)
7. Input Trim: -6 dB on both channels
8. Network Source: set to Digital
(sets the CD player as a VistaMax source)
TYPICAL DENON CD PLAYER LOGIC WIRING