46
Fryer Operation
EOF SERIES FRYERS
The following is general operational information only. Detailed procedures and instructions are covered in
subsequent sections. During operation, certain instructions and prompts will be shown on the
Upper OLED Display
to step Users through processes. Some Controller keys and indicator lights will illuminate to further guide the User.
●
POWER UP:
Place
Power Switch
in
[ON]
position. Controller will power up, then an alarm sounds. The message
“POWER
FAILURE [PRESS START TO PREHEAT]”
is shown on the
Upper Display
.
This is normal
, intended to prevent Fryer
from beginning to heat after power interruptions until attended by an operator. Pressing the
[START]
key
silences the alarm and places Fryer into
PREHEAT
mode. If the
Heat Switch
is in the
[HEAT]
position, and
temperature setpoint is higher than the current actual oil temperature, heating elements will turn
ON
and
cooking oil will begin to heat.
●
PREHEAT:
During the
PREHEAT
phase, the real-time actual oil temperature is displayed on the
Lower 7-Segment Display
.
When oil reaches the programmed setpoint, an alarm tone sounds, the
Upper OLED Display
will display message
“ALARM, STIR OIL”
. Vigorously stir the cooking oil, and press
[ALARM]
key. Typically, oil temperature will drop
when stirred. Controller has a 10 second delay and if oil temperature drops below setpoint,
PREHEAT
continues
until oil returns to setpoint.
This process helps ensure that temperature is more uniform throughout the total
volume of oil, leading to better cooking performance.
Upon reaching setpoint, the alarm sounds again and the
Upper Display
reads
“ALARM - SETPOINT REACHED”
. Pressing the
[ALARM]
key, places the Fryer in
READY
state.
●
READY STATE:
Fryer is ready for cooking. The current cooking temperature setpoint will be shown on the
Lower Display
and
the last used cooking parameters (preset or input information) are shown on the
Upper Display
.
While in
PREHEAT
or
READY
state, User can select (or change) a Menu Item Preset, see
Section 5.1.4.1, Selecting a
Menu Prese
t -OR-
User can manually set a different cooking time and/or oil temperature, see
Section 5.1.3, Set a
Manual Temperature & Cook Time
.
NOTE: If the PASSCODE ENABLE is set to ON, User cannot manually set Time without first entering the proper
password. This lockout feature provides a measure of control over cooking procedures.
● START:
Current cook settings will be shown on the
Upper OLED Display
for each Basket or Vat (dual display). To start
the cooking timer:
(a). EOF20/24
, press the
[START}
key + select BASKET side:
[4] = Left, [6] = Right, [5] = Both
(b). EOF10-10
, press the
[START]
key +
[4} for LEFT VAT or [6] for RIGHT VAT
.
+
+
+
or
+
+
EOF10-10:
EOF20 & 24:
5.1.2.
Controller - General Operation
Summary of Contents for EOF Series
