GE Vivid S5 User Manual Download Page 281 | Manualshive

Page: 281 / 690

background image

Measurement and Analysis

Vivid S5/Vivid S6 User Manual

263

R2424458-100 Rev. 2

7.

Trackball the cursor to the measurement end point.
The current velocity and pressure values are displayed in
the

Measurement result table

and are instantaneously

updated when moving the cursor.

The measurement
display color on the
spectrum changes
from green to red af-
ter completion of
the measurement.

8.

Press

SET

to anchor the end point of the measurement.

The following measurement results are displayed in the

Measurement result table

:

• Velocity and pressure at anchor point positions
• Velocity (V3) and pressure (p3) differences between

anchor point position

• Time difference (dT) between anchored points position

The measurement
display on the spec-
trum and the corre-
sponding result are
numbered.

9.

To assign a label to the measurement, see page 252.

10. Repeat steps 5 through 8 to make additional

measurements.

Manual Doppler trace measurements

Adjust Compress
and reject controls
to optimize the
Doppler signal.

1.

Generate the spectrum to be measured.

2.

Press

FREEZE

to stop the cineloop.

3.

Press

MEASURE

on the Control Panel.

Alternative: Press

CALIPER

on the con-

trol panel and press
the

MANUAL TRACE

assignable

4.

Select

Trace

in the

Measurement Menu

.

A vertical green cursor is displayed on the spectrum.

5.

Trackball the cursor to the start point on the left side of the
trace.

6.

Press

SET

to anchor the start point of the measurement.

7.

With the

trackball

, trace the Doppler envelope.

The trace can be adjusted, while tracing, by moving the
cursor backward to erase portion of the trace (or the entire
trace) and then create the trace again.

The measurement
display color on
spectrum changes
from green to red af-
ter completion of
the measurement.

8.

Press

SET

to complete the trace.

The following measurement results are displayed in the

Measurement result table

:

• Maximum and mean Velocities
• Maximum and mean pressures
• Env.

Ti

• Velocity time integral (VTI)

9.

Trackball the cursor to the start point of the next heart beat.

10. Press the

SET

to anchor the next heart beat starting point.

The heart rate (BPM) is displayed in the

Measurement

result table

.

«
...
279
280
281
282
283
...
»

Summary of Contents for Vivid S5



















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Vivid S5

Brand: Salvis Pages: 40

Brand: IDEAL Pages: 2

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: EuroLite Pages: 28

Brand: laerdal Pages: 9

Brand: RBC Bioscience Pages: 24

Brand: S&C Pages: 16

Brand: S&C Pages: 23

Brand: T&D Pages: 28

Littmann Classic II Pediatric

Brand: 3M Pages: 53

Brand: GE Pages: 289

Brand: VanGaa Lighting Pages: 7

GPSMAP 7400 Series

Brand: Garmin Pages: 8

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: Tripp Lite Pages: 24

Brand: Hedson Pages: 32

Brand: JLG Pages: 165

Brand: Labconco Pages: 174

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands