GE RTT Instruction Manual Download Page 85

Page: 85 / 94

CHAPTER 4: MOTOR MANAGEMENT & METERING THE PQM AND PQMII POWER QUALITY METERING SYSTEMS

RTT DESKTOP TEST SET– INSTRUCTION MANUAL

4.4.4

RTT to PQM/PQMII Relay Wiring Diagram

Ensure that Wet/Dry Input Type switch is set to

DRY

before applying power to the RTT

unit. The PQM/PQMII Relay accepts only dry contact connections to the RTT.

Ensure that current and voltage knobs are turned fully counter-clockwise before
applying power to the RTT unit.

Note

*Alarm and Aux1 Common terminals (44 and 41) must be hardwired together..

**The PQM/PQMII Relay doesn’t have RTD function.

Table 4–4: PQM/PQMII Relay with RTT Set to Dry

RTDs**

RTD3 +

RTD3 -

RTD3 C
RTD2 +

RTD2 -

RTD2 C
RTD1 +

RTD1 -

RTD1 C

SPARE

Contact

Outputs*

AUX 1 COMMON

---------------

RTT

ALARM COMMON

-------------------------

OUTPUT C

AUX 1 NO

-------------------------

OUTPUT 2

ALARM NO

-------------------------

OUTPUT

Contact

(Digital)

Inputs

Switch Common

-------------------------

INPUT C

INPUT 8
INPUT 7
INPUT 6
INPUT 5

Switch 4

-------------------------

INPUT 4

Switch 3

-------------------------

INPUT 3

Switch 2

-------------------------

INPUT 2

Switch 1

-------------------------

INPUT

CTs

IA (1A)

-------------------------

Ia COM

-------------------------

VTs

-------------------------

Summary of Contents for RTT































































































Search results

Summary of Contents for RTT

Reviews:

GE RTT, Instruction Manual, Page: 85 / 94

Search results

Summary of Contents for RTT

Reviews: