manualshive.com logo in svg

GE RTT, Instruction Manual, Page: 6 / 94

Share
Download
GE RTT Instruction Manual Download Page 6

2

RTT DESKTOP TEST SET– INSTRUCTION MANUAL

ABOUT YOUR NEW RTT UNIT

CHAPTER 1: GETTING STARTED

1.2

About Your New RTT Unit

1.2.1

Cautions and Warnings

Before attempting to install or use the RTT unit, it is important that all DANGER and 
CAUTION indicators in this manual are reviewed in order to prevent personal injury, 
equipment damage and/or downtime.  The above icons are used to indicate dangers, 
cautions and notes.

The standard 

note

 icon emphasizes a specific point or indicates minor problems that may 

occur if instructions are not properly followed.

The 

caution

 icon indicates that there may be possible damage to equipment or data if 

instructions are not properly followed.

The 

danger

 icon provides users with a warning about the possibility of serious or fatal 

injury to themselves or others.

1.2.2

Check the Contents of the Box

When you open the RTT box, you should find:

• one RTT unit
• one  power  cord
• one RTT-to-product connecting cable
• manual

Note

If there is any noticeable physical damage, or if any of the contents of the box are missing, 
please contact GE Multilin immediately.

1.2.3

Using this Manual

This manual is designed with the assumption that you may or may not know about the 
principles of RTT usage.  If you know little about RTT usage, please read carefully what is 
written below, bearing in mind that GE Multilin is available to fully support your questions 
about any aspect of the product.

If this is 

not

 the case, simply ignore those sections of the manual with which you are 

familiar.

The manual is structured to guide you through the entire installation and configuration 
process, from opening the box, to:

• physically connecting the associated relays
• setting up the associated relays for use with the RTT

CAUTION

NOTE

Summary of Contents for RTT































































































Reviews:

No comments