manualshive.com logo in svg

GE RTT, Instruction Manual, Page: 83 / 94

Share
Download
GE RTT Instruction Manual Download Page 83

CHAPTER 4: MOTOR MANAGEMENT & METERING                                                                           THE PQM AND PQMII POWER QUALITY METERING SYSTEMS

RTT DESKTOP TEST SET– INSTRUCTION MANUAL

79

4.4

The PQM and PQMII Power Quality Metering Systems

4.4.1

Overview

The PQM/PQMII has 3-phase current inputs with less than 0.2 VA CT Burden and 3-phase 
voltage inputs with greater than 2.2 MOhm VT burden. The PQM/PQMII has four 
programmable switch inputs designed for Dry contact connection only, and 4 Form-C 
output relays.  

All features of RTT, other than RTDs, can be applied to the PQM/PQMII. However there are 
13 unused input terminal wires, a modification is required to the cable to fit the PQM/PQMII 
terminals.

Modification of the Product Cable

For the wires related to contact inputs and contact outputs (8 in total), cut lugs off the and 
strip the wires to make them fit the PQM/PQMII terminals. 

The wires to be cut are: DOC, DO2, DO1, DIC, DI4, DI3, DI2 and DI1.

Unused Wires

For the unused wires (13 in total), it is recommended that user tape the lugs to ensure 
isolation of the contacts so that no problems are caused by wires touching.

The unused wires are: R1+, R1-, R1C, R2+, R2-, R2C, R3+, R3-, R3C, DI8, DI7, DI6 and DI5.

4.4.2

PQM/PQMII Power Quality Metering Systems Terminal Layout

FIGURE 4–23: PQM/PQMII Relay - Rear View - Terminal Layout

Summary of Contents for RTT































































































Reviews:

No comments