manualshive.com logo in svg

GE RTT, Instruction Manual, Page: 76 / 94

Share
Download
GE RTT Instruction Manual Download Page 76

72

RTT DESKTOP TEST SET– INSTRUCTION MANUAL

THE 269/269 PLUS MOTOR MANAGEMENT RELAY

                                        CHAPTER 4: MOTOR MANAGEMENT & METERING

4.3

The 269/269 Plus Motor Management Relay

4.3.1

Overview

The 269/269Plus Relay has 3-phase current inputs but no voltage inputs feature. The Relay 
provides 6 dedicated switch inputs designed for Dry contact connection only, and 4 output 
relays.  The 269/269Plus Relay monitors up to 10 RTD inputs, each RTD being field 
programmable as a 3-wire type of 100 Platinum, 100 Nickel and 120 Nickel.

All features of the RTT, other than VT, can be applied to the 269/269Plus Relay. However 
there are 4 unused input terminal wires, and a modification is required to the cable to fit  
the 269/269Plus terminals.

Modification of the Product Cable

For the wires related to contact inputs and RTDs (16 in total), cut the wire lugs, and strip the 
wire to make them fit the 269/269Plus terminals. 

The wires to be cut are: R1+, R1-, R1C, R2+, R2-, R2C, R3+, R3-, R3C, DIC, DI6, DI5, DI4, DI3, 
DI2 and DI1.

Unused Wires

For the unused wires (4 in total), it is recommended that user tape the lugs to ensure 
isolation of the contacts so that no problems are caused by wires touching.

The unused wires are: DI8, DI7, V+, and V-.

Summary of Contents for RTT































































































Reviews:

No comments