GE RTT Instruction Manual Download Page 79

Page: 79 / 94

CHAPTER 4: MOTOR MANAGEMENT & METERING THE 269/269 PLUS MOTOR MANAGEMENT RELAY

RTT DESKTOP TEST SET– INSTRUCTION MANUAL

4.3.3

RTT to 269 Wiring Diagram

Ensure that Wet/Dry Input Type switch is set to

DRY

before applying power to the RTT

unit. The 269/269 Plus Relay accepts only

DRY

contact connections to the RTT.

Ensure that current and voltage knobs are turned fully counter-clockwise before
applying power to the RTT unit.

Note

*Trip and Alarm Common terminals (30 and 33) must be hardwired together.

**The 269/269 Plus Relay doesn’t have Voltage Input function.

Table 4–3: 269/269 Plus Relay with RTT Set to Dry

RTDs

RTD3+

-------------------------

RTD3 +

RTD3-

-------------------------

RTD3 -

RTD3 COM

-------------------------

RTD3 C

RTD2+

-------------------------

RTD2 +

RTD2-

-------------------------

RTD2 -

RTD2 COM

-------------------------

RTD2 C

RTD1+

-------------------------

RTD1 +

RTD1-

-------------------------

RTD1 -

RTD1 COM

-------------------------

RTD1 C

SPARE

Contact

Outputs*

ALARM COMMON

---------------

RTT

TRIP COMMON

-------------------------

OUTPUT C

ALARM NO

-------------------------

OUTPUT 2

TRIP NO

-------------------------

OUTPUT

Contact

(Digital)

Inputs

Input Common

-------------------------

INPUT C

INPUT 8
INPUT 7

External Reset

-------------------------

INPUT 6

Emergency Restart

-------------------------

INPUT 5

Access

-------------------------

INPUT 4

Speed Switch

-------------------------

INPUT 3

Differential Input

-------------------------

INPUT 2

Spare Input

-------------------------

INPUT

CTs

Phase A (1A)

-------------------------

Phase A COM

-------------------------

VTs**

Summary of Contents for RTT































































































Search results

Summary of Contents for RTT

Reviews:

GE RTT, Instruction Manual, Page: 79 / 94

Search results

Summary of Contents for RTT

Reviews: