manualshive.com logo in svg

GE RTT, Instruction Manual, Page: 47 / 94

Share
Download
GE RTT Instruction Manual Download Page 47

CHAPTER 2: USING THE RTT ON SR SERIES RELAYS

THE SR735/737 FEEDER PROTECTION RELAY

RTT DESKTOP TEST SET– INSTRUCTION MANUAL

43

2.5

The SR735/737 Feeder Protection Relay

2.5.1

Overview

The SR735/737 Relay has 3-phase current inputs with a CT burden 0.02 VA at rated load. 
The SR745 Relay is equipped with three separate dry contact relays - TRIP, AUX and 
SERVICE. TRIP and AUX are identical non-fail-safe Form A contacts, both of which close 
whenever the unit trips. The SERVICE relay is in failsafe mode.

As the SR735/737 Relay doesn’t have Voltage Input, Contact Input and RTD features, no 
modification to the Test Cable is required. 

Unused Wires

For the unused wires (20 in total), it is recommended that user tape the lugs to ensure 
isolation of the contacts so that no problems are caused by wires touching.

The unused wires are: R1+, R1-, R1C, R2+, R2-, R2C, R3+, R3-, R3C, DIC, DI8, DI7, DI6, DI5, DI4, 
DI3, DI2, DI1, V+ and V-.

Summary of Contents for RTT































































































Reviews:

No comments