manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B650, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 206

CARESCAPE Monitor B650

 198

2062973-002

12.3.11 Detaching the Base unit

Disassemble first:
a.

12.3.2. Detaching the Interface Board

b.

12.3.3. Detaching the Frame Side Housing Decorations

c.

12.3.4. Detaching the Top Cover

d.

12.3.5. Disassembling the main unit into Rear and Front units

e.

12.4.1. Detaching the Front Unit Assembly

f.

12.4.2. Detaching the LCD Display Unit

6. Remove the four T10 screws mounting the 

AC/DC board to the back plate. 
[Torque 1.6 Nm] 

 

Hold the AC/DC board to prevent it from 
falling.

 

Reassemble in reverse order. 
- Attach the 4 screws that mount the AC/DC board [Torque 1.6 Nm]. 
- Ensure the cable clamp and the spring are in place. 
- Reattach the housing back cover so that the 4 snaps locks. 
- Attach the 1 screw that mounts the housing back cover. 
- Reconnect the AC/DC cable and the protective earth cable to the AC/DC board.
- Place the DC/DC cable in the cable holder.

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands