manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B650, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 219

 Service parts

  211

2062973-002

13 Service parts

NOTE: Perform the checkout procedure steps described in chapter 

10. Maintenance and 

checkout

 after you have replaced any service parts.

13.1 Ordering parts

To order parts, contact GE. Contact information is available at 

www.gehealthcare.com

. Make 

sure you have all necessary information at hand.

13.2 List of FRUs

#

FRU/Item  part 
number

FRU/Item description

FRU content

1

M1133991

FRU, Recorder Unit, B650 

- Includes GSI thermal printer, recorder interface 

board, aluminum EMC shield and 4 mounting 
screws

2

M1133992

FRU, E-Module Interface Board, B650

- Includes E-module interface board with 6 

mounting screws

3

M1133993

FRU, PDM Docking Mechanism, B650

- Complete PDM docking mechanism

4

M1133994

FRU, Module Frame Cover Unit Set, B650

- Includes 4 different module frame front covers, 

module frame cover unit and module frame 
back plate with its mounting screw

5

M1133995

FRU, Module Frame Assembly, B650

- Includes module frame assembly with module 

frame flex board and grounding plate

6

M1168210

 

FRU, Standard Interface Board, B650

- Includes standard interface board (2 USB, 1 RJ-

45 & 1 DVI-I), related cover plate with labelling 
and 6 mounting screws

7

M1168215

 

FRU, Advanced Interface Board, B650

- Includes advanced interface board (4 USB, 4 

RJ-45, DVI-I, ePort & Remote On) , related cover 
plate with labelling and 6 mounting screws

8

M1168219

 

FRU, AC/DC Power Supply Unit, B650

- AC/DC power supply, the DC/DC cable and 4 

mounting screws.

9

M1168221

FRU, Mains Fuses (10 pcs), B650

- FUSE, 4A, T, 250V, 5x20mm, high breaking 

capacity 1500A, IEC, UL/CSA, CCC

10

M1168224

 

FRU, Rear Unit Assembly, B650

- Complete rear unit assembly with handle unit 

and module frame mounting wall, hinges and 
release mechanism. Includes also AC inlet with 
fuses and wiring to AC/DC power supply unit, 
equipotential connector, cable clamp for power 
cord and mounting screws.

- Excludes the plastic part that has device plate 

and other labelling

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands