manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B650, Technical Manual

The GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual is a comprehensive guide for users of this advanced medical monitor. Packed with detailed instructions and troubleshooting tips, this manual can be easily downloaded for free from manualshive.com, ensuring that you have the necessary resources to utilize this innovative product effectively.

Share
Download
background image

 Troubleshooting

  167

2062973-002

PDM module issues

CPU board failure

The RS-485 communication for the E-modules is managed by the EMBC 
section of the CPU board.
- Check EMBC Frame logs for possible EMBC failures, see section 

“11.3.4”

. 

If the cause is none of the above, the problem is most likely in the CPU 
board. Replace the CPU board.

Possible cause

Recommended action

The external ePort cable is loose 
or defectice.

(PDM is connected to the ePort 
connector in advanced interface 
board)

Check that the external ePort cable is intact and properly connected to the 
PDM module and to the ePort connector in the advanced interface board.

DC/DC board failure

The VSYS supply voltage for the PDM module is generated in the DC/DC 
board. Check from the Webmin 

Hardware Statistics

 that the supply 

voltages are within specification:
- VSYS voltage (mV)
- VSYS_EPORT(mV)
- VSYS_PDM (mV)
If PDM is connected to PDM dock, DC/DC board should identify PDM and 
enable the VSYS_PDM circuit breaker on CPU carrier board to connect 
VSYS voltage to VSYS_PDM. 
If PDM is connected to ePORT, DC/DC board should identify PDM and 
enable the VSYS_EPORT circuit breaker on CPU carrier board to connect 
VSYS voltage to VSYS_EPORT. 
If VSYS voltage is out of spec, the problem is most likely in the DC/DC 
board. Replace the DC/DC board.

Advanced interface board failure. 

 

 

(PDM is connected to the ePort 
connector in advanced interface 
board)

Check the status of the VSYS OPTION voltage measured from the 
advanced interface board (see section 

“11.3.1”

 Hardware statistics).

 

 

If the VSYS OPTION voltage is out of spec, but the VSYS voltage exists in the 
DC/DC board, the problem is most likely in the advanced interface board. 
Replace the advanced interface board.

Possible cause

Recommended action

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Reviews:

No comments

Related manuals for CARESCAPE Monitor B650

Abus JC9100 ERIC Assembly And Operating Instructions preview
JC9100 ERIC
Brand: Abus Pages: 2
Abus FUSG50110 Quick Manual preview
FUSG50110
Brand: Abus Pages: 12
Abu Garcia ZENON Manual preview
ZENON
Brand: Abu Garcia Pages: 6
ABS ABS-Lock DH04 Series Manual preview
ABS-Lock DH04 Series
Brand: ABS Pages: 4
ParaBody 875 Assembly Instruction Sheet preview
875
Brand: ParaBody Pages: 5
Baileigh Industrial TN-300 Operator'S Manual preview
TN-300
Brand: Baileigh Industrial Pages: 28
Baileigh Industrial BP-3305CNC Operator'S Manual preview
BP-3305CNC
Brand: Baileigh Industrial Pages: 56
Haki 564 User Manual preview
564
Brand: Haki Pages: 24
Dakota Digital VHX-66F-BRO Installation preview
VHX-66F-BRO
Brand: Dakota Digital Pages: 5
Hagerman ECHO Manual preview
ECHO
Brand: Hagerman Pages: 4
hager EK087 Manual preview
EK087
Brand: hager Pages: 2
Ampro TECSHOW QUAD SPIDER 60 User Manual preview
TECSHOW QUAD SPIDER 60
Brand: Ampro Pages: 9
Panta Safe Light Solar Quick Start Manual preview
Solar
Brand: Panta Safe Light Pages: 2
Calrec OMEGA Installation Manual preview
OMEGA
Brand: Calrec Pages: 70
Saeyang Marathon Multi600 Manual preview
Marathon Multi600
Brand: Saeyang Pages: 21
S&C TripSaver II Quick Start Manual preview
TripSaver II
Brand: S&C Pages: 11
VDO CTC II Testing Instructions preview
CTC II
Brand: VDO Pages: 15
VDO AcquaLink Installation Instructions Manual preview
AcquaLink
Brand: VDO Pages: 20

Brands by name

Popular brands

Load more brands