GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 151

Page: 151 / 240

Troubleshooting

143

2062973-002

11.3 Webmin - Diagnostics tab

Access Webmin service interface to view hardware statistics, ping a network device, view
WLAN diagnostics and view or download log files.

11.3.1 Hardware statistics

Acquisition Information - E-
Module

•

Label, Software version, Control number, and Serial
number.

Installed S/5 Printers

•

Printer name.

Installed IX Printers

•

Printer name, hostname or IP address.

Printer Location Information

•

Printout type (Alarm Waveforms, Numeric Trends,
Reports, and Waveforms) and Printer location.

PDM License Information

•

PDM license option, status, and number of licenses.

UNITY ID Information

•

Product ID, Unity Network ID software number and
version, Date, Time, Device name and software version of
each device connected.

USB Port Information

•

Product name, Manufacturer, Vendor code, Product ID,
and Serial number.

Device information

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Search results

Summary of Contents for CARESCAPE Monitor B650

Reviews:

Related manuals for CARESCAPE Monitor B650

Brands by name

Popular brands

GE HEALTHCARE CARESCAPE Monitor B650, Technical Manual

Search results

Summary of Contents for CARESCAPE Monitor B650

Reviews:

Related manuals for CARESCAPE Monitor B650

Brands by name

Popular brands