GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 116 | Manualshive

Page: 116 / 240

background image

CARESCAPE Monitor B650

108

2062973-002

8.2.8 Patient (source) leakage current tests

This procedure measures the leakage current from an applied part connector of the device to
ground.

Perform the test in Normal Condition (NC) and in two different Single Fault Conditions (SFC):
1) earth open and 2) one of the supply conductors open at a time.

Perform test with normal and reverse polarity.
NOTE: Refer to the instructions delivered with the safety analyzer to perform this test.

NOTE: *The measuring device (MD) represents the network and voltage measuring instrument
and its frequency characters according to IEC 60601-1.
NOTE: Perform this test for all the connected parameter modules and patient connectors
specified in

1.

Configure the safety analyzer as follows (NC):

−

Polarity: NORMAL

−

Neutral: CLOSED

−

Earth (GND): CLOSED

2.

Power on the device under test.

3.

Read and record the current leakage indicated on the safety tester.

4.

Configure the safety analyzer as follows (SFC):

−

Polarity: NORMAL

−

Neutral: OPEN

−

Earth (GND): CLOSED

5.

Read and record the current leakage indicated on the safety tester.

6.

Configure the safety analyzer as follows (SFC):

−

Polarity: NORMAL

−

Neutral: CLOSED

−

Earth (GND): OPEN

7.

Read and record the current leakage indicated on the safety tester.

8.

Configure the safety analyzer as follows (SFC):

«
...
114
115
116
117
118
...
»

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Reviews:

No comments

Related manuals for CARESCAPE Monitor B650

Brand: Quincy lab Pages: 4

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 204

Brand: Bante Instruments Pages: 6

Brand: Tabi Pages: 8

Brand: Dabi Atlante Pages: 102

Brand: iHealth Pages: 8

QNET Physics and Dynamics

Brand: Quanser Pages: 4

Brand: Rane Pages: 6

Brand: Rane Pages: 27

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brand: Haag-Streit Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands