manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B650, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 216

CARESCAPE Monitor B650

 208

2062973-002

12.4.7 Replacing the WLAN Assembly FRU

Disassemble first:
a.

12.3.4. Detaching the Top Cover

 

1. Attach the WLAN card to the CPU board card 

slot as shown in the picture.

NOTE: Be careful not to bend the antenna boards 
or damage the antenna cables. 

2. Peel off the paper release liner from the 

antenna board mounting tape one at a time 
(see steps 3 and 4 below).

NOTE: Be careful not to peel off the thin adhesive 
layer, too.

3. Make sure the contact area for the antenna 

board adhesive in the Front Unit Assembly is 
clean and free of grease. Attach the antenna 
board with the longer black antenna cable to 
left side of the Front Unit Assembly as shown 
in the picture. Make sure the antenna board is 
firmly attached to the Front Unit Assembly. 
Align the loop in the antenna cable carefully 
between the display and the aluminum 
Mid-Frame as shown in the picture. 

 

The orientation of the antenna cable is 
important to ensure reliable wireless 
communication. 

4. Make sure the contact area for the antenna 

board adhesive in the Front Unit Assembly is 
clean and free of grease. 

 

Attach the antenna board with the shorter 
grey antenna cable to right side of the Front 
Unit Assembly as shown in the picture. 

 

Make sure the antenna board is firmly 
attached to the Front Unit Assembly. 

 

Align the loop in the antenna cable carefully 
between the display and the aluminum 
Mid-Frame as shown in the picture. 

 

The orientation of the antenna cable is 
important to ensure reliable wireless 
communication

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands