manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B650, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 55

 Using Webmin service interface

  47

2062973-002

National Requirements

to activate France specific defaults for the ECG HR 
adjustment range and the reminder beep behavior. 

Network

to select and configure the real-time network as the MC 
Network (CARESCAPE Network) or S/5 Network. It also 
allows the user to configure the IX Network settings.

Passwords

to change the passwords for the biomed and clinical 
users.

Power frequency

to set the power line frequency.

Printers

to configure the patient monitor to print to up to 12 laser 
printers connected on the IX Network. There are 
sub-modules for installing a printer, deleting a printer 
and for printing a test page.

Remote Service

to configure and control the Insite with Exc remote 
service tool.

Restart

to shutdown and restart the patient monitor 
automatically via Webmin.

 

NOTE: The patient must be discharged in order to enable 
monitor restart via Webmin.

Settings

to transfer platform and/or clinical settings from one 
patient monitor to another, to take backup copies of the 
settings to an external device and to restore the settings 
from an external device.

Software Management

to update patient monitor and parameter module 
software.

Time

to set the date and time settings. 

Unit and bed name

to configure the care unit name and bed name for 
patient monitors that are configured to connect to the 
MC Network.

WLAN

to configure the WLAN client settings for the MC 
Network or S/5 Network.

Webmin module

Use the module

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands