GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 117 | Manualshive

Page: 117 / 240

background image

Installation checkout

109

2062973-002

−

Polarity: REVERSED

−

Neutral: CLOSED

−

Earth (GND): OPEN

9.

Read and record the current leakage indicated on the safety tester.

10. Configure the safety analyzer as follows (SFC):

−

Polarity: REVERSED

−

Neutral: OPEN

−

Earth (GND): CLOSED

11. Read and record the current leakage indicated on the safety tester.
12. Configure the safety analyzer as follows (NC):

−

Polarity: REVERSED

−

Neutral: CLOSED

−

Earth (GND): CLOSED

13. Read and record the current leakage indicated on the safety tester.
14. Power off the device under test.
15. Repeat this test for all the connected parameter modules and patient connectors

Acceptance criteria in Normal Condition (NC):
•

All readings shall be less than or equal to 10

μ

A.

Acceptance criteria in Single Fault Condition (SFC) – earth open or one of the supply conductors
open at a time:
•

All readings shall be less than or equal to 50

μ

A.

8.2.9 Patient (sink) leakage current tests

This procedure measures the leakage current from an applied part connector of the device to
ground. Perform the test in Normal Condition (NC) with normal and reverse polarity.

NOTE: Refer to the instructions delivered with the safety analyzer to perform this test.

«
...
115
116
117
118
119
...
»

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Reviews:

No comments

Related manuals for CARESCAPE Monitor B650

Brand: NEC Pages: 54

Brand: ParaBody Pages: 5

Brand: Baileigh Industrial Pages: 28

Brand: Baileigh Industrial Pages: 56

Brand: Datavideo Pages: 48

Brand: Datavideo Pages: 34

Brand: Datavideo Pages: 3

Brand: Datavideo Pages: 34

Brand: Datavideo Pages: 8

Brand: Datavideo Pages: 10

Brand: EASTERN INSTRUMENTS Pages: 93

Brand: Pari Pages: 2

Brand: Garmin Pages: 2

Brand: M-Audio Pages: 25

Brand: Magma Pages: 16

Brand: ParaBody Pages: 6

Brand: ParaBody Pages: 11

Brand: Teac Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands