GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 211

Page: 211 / 240

Disassembly and reassembly

203

2062973-002

12.4.2 Detaching the LCD Display Unit

Disassemble first:
a.

12.3.3. Detaching the Frame Side Housing Decorations

12.3.4. Detaching the Top Cover

12.4.1. Detaching the Front Unit Assembly

1. Remove the four T10 screws with washers,

two on both sides of the LCD Display and
detach the display from the frame. [Torque 0.6
Nm]

2. Detach the LVDS cable from the LCD display.
3. Detach the Backlight Cable from the Backlight

LED Adapter Board.

NOTE: To get access to detach the cables, you
may have to lift the LCD display as showed in the
pictures.

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Search results

Summary of Contents for CARESCAPE Monitor B650

Reviews:

Brands by name

Popular brands

GE HEALTHCARE CARESCAPE Monitor B650, Technical Manual

Search results

Summary of Contents for CARESCAPE Monitor B650

Reviews:

Brands by name

Popular brands