Fujitsu SPARC Enterprise T5140 Product Notes Download Page 35

Page: 35 / 138

C H A PT E R

Known Issues

This chapter describes known issues about the SPARC Enterprise T5140 and T5240 servers.

The following sections are included in this chapter:

■

“Hardware and Mechanical Issues” on page 25

■

“Solaris OS Issues” on page 33

■

“Firmware and General Software Issues” on page 36

■

“Oracle VM Server for SPARC Issues” on page 45

Note –

For the issues already fixed in the latest version of Solaris OS or System Firmware,

see

Appendix A

. For the latest version to be supported, see

“Supported Versions of Solaris

OS and System Firmware” on page 4

Hardware and Mechanical Issues

This section describes hardware issues known to exist at this release of the SPARC
Enterprise T5140 and T5240 servers.

Hot-Swapping Fan Modules

When removing a fan module, hold the adjacent fan module in place to avoid unintentionally
dislodging the adjacent fan module.

Summary of Contents for SPARC Enterprise T5140











































































































































Search results

Summary of Contents for SPARC Enterprise T5140

Reviews:

Related manuals for SPARC Enterprise T5140

Brands by name

Popular brands

Fujitsu SPARC Enterprise T5140, Product Notes

Search results

Summary of Contents for SPARC Enterprise T5140

Reviews:

Related manuals for SPARC Enterprise T5140

Brands by name

Popular brands