Fujitsu SPARC Enterprise T5140 Product Notes Download Page 46

Page: 46 / 138

SPARC Enterprise T5140 and T5240 Servers Product Notes • November 2012

Confirm whether either of the following part numbers is displayed in the output from

/SYS/PADCRD

command.

[Using ALOM CMT compatible shell]

Confirm whether either of the following part numbers is displayed in the output from

showfru /SYS/PADCRD

command.

Firmware and General Software Issues

The following are known firmware and general software issues.

fru_part_number = 5413512

fru_part_number = 5413513

/Partner_Part_NumberR/Partner_Part_Number: CF005413512REVxx

/Partner_Part_NumberR/Partner_Part_Number: CF005413513REVxx

TABLE 3-4

Firmware and General Software Issues

CR ID

Description

Workaround

7110871

When you change "

/SP/services/https

weak_ciphers

" from

disabled

enabled

, or

change it from

enabled

disabled

, you may

fail in restarting the ILOM Web service.
When this event occurred, it becomes unable to
connect to BUI of ILOM.

None.
To recover from this event, reset ILOM.

Summary of Contents for SPARC Enterprise T5140











































































































































Search results

Summary of Contents for SPARC Enterprise T5140

Reviews:

Related manuals for SPARC Enterprise T5140

Brands by name

Popular brands

Fujitsu SPARC Enterprise T5140, Product Notes

Search results

Summary of Contents for SPARC Enterprise T5140

Reviews:

Related manuals for SPARC Enterprise T5140

Brands by name

Popular brands