manualshive.com logo in svg

Fujitsu SPARC Enterprise M4000, Reference Manual, Page: 369 / 444

Share
Download
Fujitsu SPARC Enterprise M4000 Reference Manual Download Page 369

shownetwork(8)

System Administration

433

server.

EXIT STATUS

The following exit values are returned:

SEE ALSO

applynetwork

(8)

, setnetwork

(8)

XSCF>

shownetwork -a

xscf#0-lan#0
 Link encap:Ethernet  HWaddr 00:00:00:12:34:56
 inet addr: 192.168.11.10  Bcast: 192.168.11.255  Mask:255.255.255.0
 UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
 RX packets:54424 errors:0 dropped:0 overruns:0 frame:0
 TX packets:14369 errors:0 dropped:0 overruns:0 carrier:0
 collisions:0 txqueuelen:1000
 RX bytes:12241827 (11.3 MiB)  TX bytes:1189769 (0.9 MiB)
 Base address:0x1000

xscf#0-lan#1
 Link encap:Ethernet  HWaddr 00:00:00:12:34:57
 inet addr:192.168.10.11  Bcast: 192.168.10.255  Mask:255.255.255.0
 UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
 RX packets:54424 errors:0 dropped:0 overruns:0 frame:0
 TX packets:14369 errors:0 dropped:0 overruns:0 carrier:0
 collisions:0 txqueuelen:1000
 RX bytes:20241827 (19.3 MiB)  TX bytes:2089769 (1.9 MiB)
 Base address:0x1000

xscf#0-if  Link encap:Ethernet  HWaddr 00:00:00:00:00:00
 inet addr:192.168.10.128  Bcast:192.168.10.255  Mask: 255.255.255.0
 UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
 RX packets:54424 errors:0 dropped:0 overruns:0 frame:0
 TX packets:14369 errors:0 dropped:0 overruns:0 carrier:0
 collisions:0 txqueuelen:1000
 RX bytes:0 (0.0 B)  TX bytes:17010 (16.6 KiB)
 Base address:0x1000

xscf#1-lan#0
 HWaddr 00:00:00:12:34:59
 inet addr:192.168.10.12  Mask:255.255.255.0

xscf#1-lan#1
 HWaddr 00:00:00:12:34:60

xscf#1-if
 HWaddr 00:00:00:12:34:61
XSCF>

0

Successful completion.

>0

An error occurred.

Summary of Contents for SPARC Enterprise M4000





























































































































































































































































































































































































































































Reviews:

No comments