Fujitsu SPARC Enterprise M4000 Reference Manual Download Page 25

Page: 25 / 444

Intro(8)

System Administration

man

display manual pages of specified XSCF shell command

moveboard

move an eXtended System Board (XSB) from the current
domain to another

nslookup

refer to the DNS server for the host

password

manage user passwords and expiration settings

poweroff

turn off the power to the specified domain

poweron

turn on the power to the specified domain

prtfru

display FRUID data on the system and External I/O
Expansion Unit

rebootxscf

reset the XSCF

replacefru

replace a field replaceable unit (FRU)

reset

reset the specified domain

resetdateoffset

reset the time subtraction between XSCF and the domain.

sendbreak

send a break signal to the specified domain

setaltitude

set the altitude of the system

setarchiving

configure the log archiving functionality

setaudit

manage the system auditing functionality

setautologout

set the session timeout time of the XSCF shell

setcod

set up the Capacity on Demand (COD) resources used for
domains

setdate

set the date and time of XSCF

setdcl

set a domain component list (DCL)

setdomainmode

set a domain mode

setdomparam

forcibly rewrite OpenBoot PROM environment variables

setdscp

set the IP address assignments for the Domain to Service
Processor Communications Protocol (DSCP)

setdualpowerfeed

set dual power feed mode

setemailreport

set up the email report configuration data

sethostname

set a host name and domain name for an XSCF unit

sethttps

start or stop the HTTPS service, which is used in the XSCF
network. This command also performs authentication-
related settings.

Summary of Contents for SPARC Enterprise M4000





























































































































































































































































































































































































































































Search results

Summary of Contents for SPARC Enterprise M4000

Reviews:

Fujitsu SPARC Enterprise M4000, Reference Manual, Page: 25 / 444

Search results

Summary of Contents for SPARC Enterprise M4000

Reviews: