manualshive.com logo in svg

Fujitsu SPARC Enterprise M4000, Reference Manual, Page: 368 / 444

Share
Download
Fujitsu SPARC Enterprise M4000 Reference Manual Download Page 368

shownetwork(8)

432

XSCF Reference Manual • Last Revised June 2007

EXAMPLE 4

Displays the information for XSCF-LAN#0 on XSCF Unit 0.

EXAMPLE 5

Displays the information for the takeover IP address for XSCF-LAN#0.

EXAMPLE 6

Displays the current settings of XSCF network.

EXAMPLE 7

Displays the information for XSCF unit 0 and XSCF unit 1 in the high-end

XSCF>

shownetwork xscf#0-lan#0

xscf#0-lan#0
 Link encap:Ethernet  HWaddr 00:00:00:12:34:56
 inet addr:192.168.11.10  Bcast:192.168.11.255  Mask 255.255.255.0
 UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
 RX packets:54424 errors:0 dropped:0 overruns:0 frame:0
 TX packets:14369 errors:0 dropped:0 overruns:0 carrier:0
 collisions:0 txqueuelen:1000
 RX bytes:14541827 (13.8 MiB)  TX bytes:1459769 (1.3 MiB)
 Base address:0x1000

XSCF>

shownetwork lan#0

lan#0     Link encap:Ethernet  HWaddr 00:00:00:12:34:56
 inet addr:192.168.1.10   Bcast:192.168.1.255   Mask:255.255.255.0
 UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
 Base address:0xe000

XSCF>

shownetwork -i

Active Internet connections (without servers)
Proto Recv-Q Send-Q Local Address

Foreign Address

State

tcp

0

0 xx.xx.xx.xx:telnet

xxxx:1617

ESTABLISHED

Summary of Contents for SPARC Enterprise M4000





























































































































































































































































































































































































































































Reviews:

No comments