manualshive.com logo in svg

Fujitsu SPARC Enterprise M4000, Reference Manual, Page: 324 / 444

Share
Download
Fujitsu SPARC Enterprise M4000 Reference Manual Download Page 324

showenvironment(8)

294

XSCF Reference Manual • Last Revised November 2007

EXTENDED

DESCRIPTION

For some systems, voltage margin is set for each entire system. In such a case, the
voltage margin is displayed along with the value of the voltage sensor.

EXAMPLES

EXAMPLE 1

Displays the intake temperature and humidity of the system.

EXAMPLE 2

Displays temperature information about the system and each component.

XSCF>

showenvironment

Temperature:30.71C
Humidity:90.05%

XSCF>

showenvironment temp

Temperature:30.71C
CMU#0:30.71C
 CPUM#0-CHIP#0:30.71C
 CPUM#1-CHIP#0:30.71C
 CPUM#2-CHIP#0:30.71C
 CPUM#3-CHIP#0:30.71C
CMU#1:30.71C
 CPUM#0-CHIP#0:30.71C
 CPUM#1-CHIP#0:30.71C
 CPUM#2-CHIP#0:30.71C
 CPUM#3-CHIP#0:30.71C
CMU#2:30.71C
 CPUM#0-CHIP#0:30.71C
 CPUM#1-CHIP#0:30.71C
 CPUM#2-CHIP#0:30.71C
 CPUM#3-CHIP#0:30.71C
CMU#3:30.71C
 CPUM#0-CHIP#0:30.71C
 CPUM#1-CHIP#0:30.71C
 CPUM#2-CHIP#0:30.71C
 CPUM#3-CHIP#0:30.71C

Summary of Contents for SPARC Enterprise M4000





























































































































































































































































































































































































































































Reviews:

No comments