Fujitsu 8FX Hardware Manual Download Page 193

Page: 193 / 650

MB95630H Series

MN702-00009-2v0-E

FUJITSU SEMICONDUCTOR LIMITED

171

CHAPTER 11 8/16-BIT COMPOSITE TIMER

11.14 Registers

●

PWM timer function (variable-cycle)

The 8/16-bit composite timer n0 data register (Tn0DR) and 8/16-bit composite timer n1 data

starts operating (Tn0CR1/Tn1CR1:STA = 1), the value of each register is transferred to the

latch in the 8-bit comparator and the two counters start counting from timer output "L". When

the Tn0DR value transferred to the latch matches the timer n0 counter value, the timer output

becomes "H" and the counting continues until the Tn1DR value transferred to the latch

matches the timer n1 counter value. When the Tn1DR value transferred to the latch of the 8-bit

comparator matches the timer n1 counter value, the values of the Tn0DR register and the

T01DR register are transferred again to the latch and the counter performs the next PWM cycle

of counting.

The current count value can be read from this register. In 16-bit operation, write the upper

timer data to Tn1DR and lower timer data to Tn0DR, and read Tn1DR first and then Tn0DR.

●

PWC timer function

The 8/16-bit composite timer data register (Tn0DR/Tn1DR) is used to read PWC measurement

results. When PWC measurement is completed, the counter value is transferred to this register

and the BF bit is set to "1".

When the 8/16-bit composite timer data register is read, the BF bit is set to "0". While the BF

bit is "1", no data is transferred to the 8/16-bit composite timer data register.

There is an exception. With the F[3:0] bits in the Tn0CR0/Tn1CR0 register having been set to

"0b1001", even though the BF bit is set to "1", the "H" pulse measurement result is transferred

to the 8/16-bit composite timer data register, while the cycle measurement result is not

transferred to the 8/16-bit composite timer data register. Therefore, in order to perform cycle

measurement, the "H" pulse measurement result must be read before a cycle is completed. In

addition, the result of "H" pulse measurement and that of cycle measurement are lost if they are

not read before the completion of the next "H" pulse.

When reading the 8/16-bit composite timer data register, ensure that the BF bit is not cleared

accidentally.

If new data is written to the 8/16-bit composite timer data register, the stored measurement data

is replaced with the new data. Therefore, do not write data to the register. In 16-bit operation,

write the upper timer data to Tn1DR and lower timer data to Tn0DR, and read Tn1DR first and

then Tn0DR.

●

Input capture function

The 8/16-bit composite timer data register (Tn0DR/Tn1DR) is used to read input capture

results. When an edge specified is detected, the counter value is transferred to the 8/16-bit

composite timer data register.

If new data is written to the 8/16-bit composite timer data register, the stored measurement data

is replaced with the new data. Therefore, do not write data to the register. In 16-bit operation,

write the upper timer data to Tn1DR and lower timer data to Tn0DR, and read Tn1DR first and

then Tn0DR.

Summary of Contents for 8FX











































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands

Fujitsu 8FX, Hardware Manual

Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands