Fujitsu 8FX Hardware Manual Download Page 225

Page: 225 / 650

MB95630H Series

MN702-00009-2v0-E

FUJITSU SEMICONDUCTOR LIMITED

203

CHAPTER 14 LIN-UART

14.2 Configuration

●

LIN synch break/synch field detection circuit

This circuit detects a LIN synch break when the LIN master node transmits a message header.

The LBD flag is set when the LIN synch break is detected. An internal signal is output to 8/16-

bit composite timer in order to detect the first and the fifth falling edges of the LIN synch field

and to measure the actual serial clock synchronization transmitted by the master node.

●

LIN synch break generation circuit

This circuit generates a LIN synch break with a length set.

●

Bus idle detection circuit

If this circuit detects that no transmission or reception is in progress, it sets the TBI flag bit or

the RBI flag bit to "1" respectively.

●

LIN-UART serial control register (SCR)

Its operating functions are as follows:

•

Setting the use of the parity bit

•

Parity bit select

•

Setting stop bit length

•

Setting data length

•

Selecting the frame data format in operating mode 1

•

Clearing the error flag

•

Enabling/disabling transmission

•

Enabling/disabling reception

●

LIN-UART serial mode register (SMR)

Its operating functions are as follows:

•

Selecting the LIN-UART operating mode

•

Selecting the clock input source

•

Selecting between one-to-one connection to the external clock and connection to the reload
counter

•

Resetting the dedicated reload timer

•

LIN-UART software reset (maintaining register settings)

•

Enabling/disabling output to the serial data pin

•

Enabling/disabling output to the clock pin

●

LIN-UART serial status register (SSR)

Its operating functions are as follows:

•

Checking transmission/reception or error status

•

Selecting the transfer direction (LSB-first or MSB-first)

•

Enabling/disabling receive interrupts

•

Enabling/disabling transmit interrupts

Summary of Contents for 8FX











































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands

Fujitsu 8FX, Hardware Manual

Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands