Fujitsu 8FX Hardware Manual Download Page 34 | Manualshive

Page: 34 / 650

background image

MB95630H Series

12

FUJITSU SEMICONDUCTOR LIMITED

MN702-00009-2v0-E

CHAPTER 2 CPU
2.2 General-purpose Register

■

Features of General-purpose Registers

The general-purpose register has the following features.

•

High-speed access to RAM with short instructions (general-purpose register addressing).

•

Grouping registers into a block of register banks facilitates data protection and division of
registers in terms of functions.

A general-purpose register bank can be allocated exclusively to an interrupt service routine or a

vector call (CALLV #0 to #7) service routine. For instance, the fourth register bank is always

assigned to the second interrupt.

Data of a general-purpose register before an interrupt can be saved to a dedicated register bank

by just specifying that register bank at the beginning of an interrupt service routine. This

therefore eliminates the need to save data of a general-purpose register in a stack, thereby

enabling the CPU to receive interrupts at high speed.

Note:

In an interrupt service routine, include one of the following in a program to ensure that
values of the interrupt level bits (CCR:IL[1:0]) of the condition code register are not
modified when modifying a register bank pointer (RP) to specify a register bank.

•

Read the interrupt level bits and save their values before writing a value to the RP.

•

Directly write a new value to the RP mirror address "0x0078" to update the RP.

•

As for a product whose RAM size is 256 bytes, the area available for general-purpose
registers is from "0x0100" to "0x018F", which is half of that of the product whose RAM
size is 512 bytes or above. Therefore, when using a program development tool such
as a C compiler to set a general-purpose register area, ensure that the area used as a
general-purpose register area does not exceed the size of RAM installed.

«
...
32
33
34
35
36
...
»

Summary of Contents for 8FX











































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8FX

Brand: XMG Pages: 5

Brand: NAD Pages: 2

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 5

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

WJMPU955 - PROCESSING UNIT - TMU

Brand: Panasonic Pages: 62

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

ARM Cortex-A9 MPCore

Brand: Dave Embedded Systems Pages: 67

kontron COMe-cEL6

Brand: S&T Pages: 99

Brand: Accom Pages: 15

Wisenet PRN-6400B4

Brand: Hanwha Techwin Pages: 14

Brand: ZALMAN Pages: 9

F-Tile SDI II Intel Agilex

Brand: Intel Pages: 39

Brand: axing Pages: 52

Brand: Aurora Pages: 6

Brand: Aaeon Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands