Fujitsu 8FX Hardware Manual Download Page 131

Page: 131 / 650

MB95630H Series

MN702-00009-2v0-E

FUJITSU SEMICONDUCTOR LIMITED

109

CHAPTER 8 HARDWARE/SOFTWARE WATCHDOG TIMER

8.5 Notes on Using Watchdog Timer

8.5

Notes on Using Watchdog Timer

This section provides notes on using the watchdog timer.

■

Notes on Using Watchdog Timer

●

Stopping the watchdog timer

Software watchdog timer

Once activated, the watchdog timer cannot be stopped until a reset is generated.

●

Selecting the count clock

Software watchdog timer

The count clock switch bits (WDTC:CS[1:0], CSP) can be modified only when the watchdog

control bits (WDTC:WTE[3:0]) are set to "0b0101" after the activation of the watchdog timer.

The count clock switch bits cannot be set by a bit manipulation instruction. Moreover, the bit

settings should not be changed once the timer is activated.

In subclock mode or sub-CR clock mode, the time-base timer does not operate because the

main clock, the main CR clock, or the main CR PLL clock stops oscillating.

In order to make the watchdog timer operate in subclock mode or sub-CR clock mode, it is

necessary to select the watch prescaler as the count clock beforehand and set WDTC:CS[1:0],

CSP to "0b100" or "0b110" or "0bXX1" (X = 0 or 1).

●

Clearing the watchdog timer

Clearing the timer (time-base timer, watch prescaler or sub-CR timer) used as the count clock

of the watchdog timer also clears the counter of the watchdog timer.

The counter of the watchdog timer is cleared when the watchdog timer transits to sleep mode,

stop mode, or watch mode, except in the case of activating hardware watchdog timer whose

operation in standby mode has been enabled.

●

Programming precaution

When creating a program in which the watchdog timer is cleared repeatedly in the main loop,

set the processing time of the main loop including the interrupt processing time to the

minimum watchdog timer interval time or shorter.

●

Hardware watchdog timer (operation in standby mode has been enabled)

The hardware watchdog timer does not stop in stop mode, sleep mode, time-base timer mode

or watch mode. Therefore, the hardware watchdog timer is not cleared by the CPU even if the

internal clock stops. (in stop mode, sleep mode, time-base timer mode or watch mode).

Regularly release the device from standby mode and clear the watchdog timer. However,

depending on the setting of the oscillation stabilization wait time setting register, a watchdog

reset may be generated after the CPU wakes up from stop mode in subclock mode or sub-CR

clock mode.

Take account of the setting of the subclock stabilization wait time when selecting the subclock.

Summary of Contents for 8FX











































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands

Fujitsu 8FX, Hardware Manual

Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands