Fujitsu 8FX Hardware Manual Download Page 528

Page: 528 / 650

MB95630H Series

506

FUJITSU SEMICONDUCTOR LIMITED

MN702-00009-2v0-E

CHAPTER 24 I

C BUS INTERFACE

24.6 Operations and Setting Procedure Example

■

General Call Address

A general call address consists of the start address byte (0x00) and the second address byte that

follows. To use a general call address, you must set IBCR1n:GACKE=1 before the

acknowledge of the first byte general call address. In addition, the acknowledgment for the

second address byte can be controlled as shown below.

Figure 24.6-2 General Call Operation

If this module sends a general call address at the same time as another device, you can

determine whether the module successfully seized control of the bus by checking whether

arbitration lost was detected when the second address byte was transferred. If arbitration lost

was detected, the module goes to slave mode and continues to receive data from the master.

First-byte general call address

Second-byte general call address

ACK

ACK/NACK

Slave mode

(a) General call operation in slave mode

Master mode

(b) General call operation in master mode (Start from GACKE = 1 with no AL.)

Master mode

(d) General call operation in master mode (Start from GACKE = 0 with no AL.)

Master mode

(e) General call operation in master mode (Start from GACKE = 0 with AL generated by second address.)

GACKE=1

GACKE=0

ACK :

Acknowledgment

NACK : No acknowledgment
GCA :

General call address

AL :

Arbitration lost

When IBCR1n:GACKE = 1,
ACK is given and IBSRn:GCA is set.

IBCR1n:INT is set at 9th SCLn

↓

Set IBCR0n:INTS = 1.

IBCR1n:INT is set at 9th SCLn

↓

Read IBSRn:LRB.

IBCR1n:INT is set at 8th SCLn

↓

Read IDDRn and control ACK/NACK by IBCR1n:DACKE.
To read IBSRn:LRB, set INTS = 0.

IBCR1n:INT is set at 8th

SCLn

↓

Read IDDRn and control ACK/NACK by IBCR1n:DACKE.
To read IBSRn:LRB, set INTS = 0.

ACK is given and IBSRn:GCA is set.

IBCR1n:INT is set at 9th SCLn

↓

Set IBCR0n:INTS = 1 and GACKE = 0.

IBCR1n:INT is set at 9th

SCLn

↓

Set IBCR0n:INTS = 1 and GACKE = 0.

IBCR1n:INT is set at 9th SCLn

↓

Read IBSRn:LRB.

IBCR1n:INT is set at 9th

SCLn

↓

Read IBSRn:LRB.

IBCR1n:INT is set at 8th

SCLn

↓

Read IDDRn and control ACK/NACK by IBCR1n:DACKE.
To read IBSRn:LRB, set INTS = 0.

IBCR1n:INT is set at 9th

SCLn

↓

Read IBSRn:LRB.

IBCR1n:INT is set at 9th

SCLn

↓

Read IBSRn:LRB.

IBCR1n:INT is set at 8th SCLn

↓

Set INTS = 0 to read IBSRn:LRB.

AL is generated by second address and switches to slave mode.

IBCR1n:INT is set at 9th

SCLn

↓

Set IBCR0n:INTS = 1.

ACK is not given and IBSRn:GCA is not set.

IBCR1n:INT is set at 9th

SCLn

↓

Set IBCR0n:INTS = 1.

ACK is not given and IBSRn:GCA is not set.

AL is generated by second address, IBSRn:GCA is set,
and switches to slave mode.

IBCR1n:INT is set at 8th SCLn

↓

To read IBSRn:LRB, set INTS = 0.

GCA is cleared.

First-byte general call address

Second-byte general call address

ACK

ACK/NACK

First-byte general call address

Second-byte general call address

ACK

ACK/NACK

First-byte general call address

Second-byte general call address

NACK

ACK/NACK

First-byte general call address

Second-byte general call address

NACK

ACK/NACK

Summary of Contents for 8FX











































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands

Fujitsu 8FX, Hardware Manual

Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands