Fujitsu 8FX Hardware Manual Download Page 114

Page: 114 / 650

MB95630H Series

FUJITSU SEMICONDUCTOR LIMITED

MN702-00009-2v0-E

CHAPTER 7 TIME-BASE TIMER
7.4 Operations and Setting Procedure
Example

7.4

Operations and Setting Procedure Example

This section describes the operations of the interval timer function of the time-
base timer.

■

Operations of Time-base Timer

The counter of the time-base timer is initialized to "0xFFFFFF" after a reset, and starts

counting while being synchronized with the main clock divided by two, or with the main CR

clock or with the main CR PLL clock.

The time-base timer continues to count down as long as the main clock, the main CR clock or

the main CR PLL clock is oscillating. Once the main clock, the main CR clock or the main CR

PLL clock stops, the counter stops counting and is initialized to "0xFFFFFF".

To use the interval timer function, do the settings shown in Figure 7.4-1.

Figure 7.4-1 Settings of Interval Timer Function

When the time-base timer clear bit in the time-base timer control register (TBTC:TCLR) is set

to "1", the counter of the time-base timer is initialized to "0xFFFFFF" and continues to count

down. When the selected interval time has elapsed, the time-base timer interrupt request flag

bit in the time-base timer control register (TBTC:TBIF) becomes "1". In other words, an

interrupt request is generated at each interval time selected, based on the time when the counter

was last cleared.

■

Clearing Time-base Timer

With the output of the time-base timer being used in other peripheral functions, clearing the

time-base timer affects their operations in various ways such as changing the count time of a

peripheral function.

When clearing the counter by using the time-base timer clear bit (TBTC:TCLR), modify the

settings of other peripheral functions whenever necessary so that clearing the counter does not

have any unexpected effect on them.

When the output of the time-base timer is selected as the count clock for the watchdog timer,

clearing the time-base timer also clears the watchdog timer.

The time-base timer is cleared not only by the TCLR bit, but also when the main clock, the

main CR clock, or the main CR PLL clock is stopped and the oscillation stabilization wait time

is necessary. The time-base timer is cleared in the following situations:

•

The device transits from the main clock mode, the main CR clock mode or the main CR
PLL clock mode to the stop mode.

•

The device transits from the main clock mode, the main CR clock mode or the main CR
PLL clock mode to the subclock mode or the sub-CR clock mode.

•

At power-on

•

At low-voltage detection reset

1
0

Bit to be used

:
:

Set to "1".
Set to "0".

TBIF

TBTC

TBIE

TBC3

TBC2

TBC1

TBC0

TCLR

bit7

bit6

bit5

bit4

bit3

bit2

bit1

bit0

Summary of Contents for 8FX











































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands

Fujitsu 8FX, Hardware Manual

Search results

Summary of Contents for 8FX

Reviews:

Related manuals for 8FX

Brands by name

Popular brands