Fujitsu 10 ppm User Manual Download Page 78

Page: 78 / 146

User’s Manual

4-3

ENHANCING &
CUSTOMIZING

Notice:

Do not touch any connector contacts to avoid possible electrostatic
damage to the printer.

Install the RAM card.

Push

its top edge downwards so
that holes of the card align
with locating pins of the
connector and the card is
secured by retaining clips.

Important:

When installing two RAM cards, first install the lower one, and then the
upper one.

Turn power on. If necessary, change buffer memory assignment (page
protect or jam recovery) using the control panel.

To remove an unsealed RAM
card push out the retaining
clips. When, the card slants
outwards pull the card to
remove.

Alternate emulations are offered with emulation cards. You can use these
emulations to connect your printer to different computers. The FPS card
(PostScript Level 2 compatible) is available.

The installation procedure is the same as that for the RAM card.

To install an alternate emulation, follow these steps:

1. If RAM cards are already installed, remove them.

2. Insert the emulation card into the bottom

black

connector.

3. Reinstall the RAM cards.

Installing an Alternate Emulation

☞

✍

Installing an
Alternate
Emulation

Summary of Contents for 10 ppm



















































































































































Search results

Summary of Contents for 10 ppm

Reviews:

Related manuals for 10 ppm

Brands by name

Popular brands

Fujitsu 10 ppm, User Manual

Search results

Summary of Contents for 10 ppm

Reviews:

Related manuals for 10 ppm

Brands by name

Popular brands