Fujitsu 10 ppm User Manual Download Page 65

Page: 65 / 146

3-20

User’s Manual

Handling Paper

This printer can print on a wide range of paper sizes, but the size is
limited when using paper trays.
• When using a paper tray, the size is:

Paper size (physical)

Dimensions

A4 (European letter size)

210

297 mm

148

210 mm

Letter (US letter size)

8.5

Legal (US legal size)

8.5

Executive

7.25

10.5

• When using the manual feed slot, the size is:

Minimum:

100 mm wide

148 mm long (3.94

5.81

inches)

Maximum:

216 mm wide

360 mm long (8.5

14.13

inches)

• When using the MFF (option), the size is:

Paper size (physical)

Dimensions

210

297 mm

148

210 mm

Letter

8.5

inches

Legal

8.5

inches

Executive

7.25

10.5

inches

Envelope COM-10

4 1/8

9.5

inches

Envelope Monarch

3 7/8

7.5

inches

Envelope C5

162

229 mm

Envelope DL

110

220 mm

Envelope B5

176

250

Summary of Contents for 10 ppm



















































































































































Search results

Summary of Contents for 10 ppm

Reviews:

Related manuals for 10 ppm

Brands by name

Popular brands

Fujitsu 10 ppm, User Manual

Search results

Summary of Contents for 10 ppm

Reviews:

Related manuals for 10 ppm

Brands by name

Popular brands